Specialty socket set designed to easily remove rounded, damaged or corroded nuts, bolts, wheel lugs, pipes, pipe nipples or studs. Fits sizes 3/8 to 3/4 in. and 10mm to 19mm plus punch.
Average Customer Rating:
2.7 out of 5
4 of 10 (40%) customers would recommend this product to a friend.
great product,October 2, 2008
By tommya05from phoenix, az
"After spending nearly one month trying to remove a bolt from my transmission housing, I was referred to bolt-out. The bolt in question was very rounded from all the previously failed attempts (I'd tried twice along with two different auto mechanics--one of which was the dealership). Five minutes with the bolt-out and the bolt was out. great product. FYI, had to hammer the bolt-out socket onto the bolt in order for it to bite."
The Right Tool For The Right Job!!,June 26, 2008
By Mokifrom Melbourne FL.
"I lost the key for the lug nut locks on my car. Tried different options and none of them worked. With this set in less than 10 sec per nut I was done!!! I did not used an impact gun but gat the job done quick and safe with no damage to the rims. THANKS!!!"
nuke pump,April 9, 2008
By Anonymousfrom lancaster pa
"Our pump had 8 bolts with rounded off heads. While turning socket with wrench my pal would hit top of socket with short handled maul. We did split the 1st socket and my Lancaster county Sears replaced the set. My work place (nuke plant) wants to buy another set for an up coming job."
Low Rate tool NO WARRANTY,December 31, 2007
By BrianWVfrom WV
"I was given this set as a gift and it is trash. The socket I was using split down the side and blew apart. These are supposed to be impact quality THEY ARE NOT. Had I been using an impact wrench I would have had half the socket imbedded in my skull. I was using a 3/8 breaker bar. I took them back to the store only to find out they are NOT COVERED BY WARRANTY. The employees didn't even know these had no warranty. Had the manager not been at the register they would have traded them out. These are sold in the same section as the other sockets that are warranted. Sears will not replace these DO NOT BY THESE Buy Irwin brand , they have a warranty."
Excellent tool,September 17, 2007
By TonHefrom Portland, TX
Value
55
Performance
55
Reliability
55
Workmanship
55
"I used this impact tool set to remove hardened, rusted nuts off '66 Corvair head studs shipped to me from Wisconsin(even after reading the negative reviews). These tools worked flawlessly, and saved a good set af aluminum cylinder heads from destruction from the grinder or torch. And, they looked like new after removing 12 seized, rusted, rounded over, torqued-on, 41 year old nuts. Highly recommended. Tony H."
Dont Buy This !!!No Warrenty!!!,June 7, 2007
By JeremyAutomotiveTechfrom Sioux Falls, SD
Value
15
Performance
15
Reliability
15
Workmanship
15
"I used the 13mm bolt remover for the first time and it worked great (Mind you they claim it can be used with an impact gun). Craftsman claims that it has a "Guarenteed Forever" hand tool polocy come to find out that this hand tool does not. I used the 13mm bolt remover the second time and it sheared the sockets insides out like it was butter. I get to the store to find out that it is a non guarenteed item and might i add the guy was very rood about me asking for a warrenty exchange. So I would not buy this item again and I would watch out for the misconseption about "Guarenteed Forever" on hand tools. I dont know about you but i think this is a hand tool."
Not for impact use!,May 16, 2007
By TimothyAfrom Evesham, NJ
Value
25
Performance
25
Reliability
15
Workmanship
15
"Craftsman claims that this set is impact-grade, yet the second time I used my 13 mm bolt-out it blew in half as soon as hit the trigger on my impact wrench! To add insult to injury I brought it into Sears only to find out it had no warranty. The design does a great job of removing rounded off and rusty fasteners, but the material it is made of is far too brittle and too thin. If you own this set stick to hand tools, but if you don't avoid it and buy the standard bolt-out instead."
craftsman bolt out,April 3, 2007
By richiecfrom ithaca ny
Value
15
Performance
15
Reliability
15
Workmanship
15
"I thought that I was buying a good tool but I used bolt out 13mm socket one and it broke like it was made from ceramic--I thought no problem its gaurenteed---sears says no-warrenty and I can't just buy that one to make kit again and sell this junk to someone else. very disappionted and will stop buying craftsman tools!!!!!"
IMPACT BOLTOUTS,March 19, 2007
By RJMSMETZfrom MT VERNON WASHINGTON
Value
15
Performance
15
Reliability
15
Workmanship
15
"MORE LIKE BLOW OUTS... USED THE 14MM/ 9/16 BOLT OUT ONCE WORKED LIKE A CHAMP. THE SECOND TIME IT SPLIT LIKE IT WAS MADE OUT OF PLASTIC. *** NO BIG DEAL ITS A CRAFTSMAN*** WAS I WRONG
